Ero sivun ”R58.en” versioiden välillä

Radioamatööriwikistä
Siirry navigaatioon Siirry hakuun
>Oh3bk
pEi muokkausyhteenvetoa
>Oh3bk
(RFCDAC-CTCSS-parametrien ja wishlistin päivitys)
Rivi 5: Rivi 5:
----
----
== CTCSS generation/encoding for non-repeater use ==
== CTCSS generation/encoding for non-repeater use ==
Requires R58 firmware 3.Yz or greater.
Introduced at firmware 3.Yz, requires R58 firmware 3.Zi or or higher to operate as follows:


The RX front-end DAC can be used for generating CTCSS waveform for TX. The modification is easy and requires just two components, a polystyrene 100n capacitor and a 10k resistor to be installed on the A8 audio board beneath the P8 processor board. All settings are adjusted by the handset.
The RX front-end DAC can be used for generating CTCSS waveform for TX. The modification is easy and requires just two components, a polystyrene 100n capacitor and a 10k resistor to be installed on the A8 audio board beneath the P8 processor board. All settings are adjusted by the handset.
Rivi 15: Rivi 15:
=== Parameters: ===
=== Parameters: ===


'''<tt>GE:CtCSSt</tt>''' CTCSS frequency in hertz. For frequencies with decimals, use the nearest full hz. eg. 118.8hz would be 119 and 74.4hz would be 74
'''<tt>01 GE:CtCSSt</tt>''' CTCSS frequency in hertz. For frequencies with decimals, use the nearest full Hz. eg. 118.8 Hz would be 119 and 74.4 Hz would be 74


'''<tt>PH:CtCGEn</tt>''' option <tt>rFcdAc</tt> selects the RX RFC DAC output to be used as CTCSS waveform generator during TX.
'''<tt>816 PH:CtCGEn</tt>''' option <tt>rFcdAc</tt> selects the RX RFC DAC output to be used as CTCSS waveform generator during TX.


'''<tt>PH:CtGAin</tt>''' sets the amplitude of the generated waveform.
'''<tt>817 PH:CtHAnG</tt>''' sets the TOC time in millseconds. TOC eliminates the squelch crash at the receiving station, suspending the CTCSS tone transmission prior to the drop of the carrier.


'''<tt>PH:CtHAnG</tt>''' sets the TOC time in millseconds. TOC eliminates the squelch crash at the receiving station, suspending the CTCSS tone transmission prior to the drop of the carrier.
'''<tt>818 PH:CtGAin</tt>''' sets the amplitude of the generated waveform, must fit between rfc and abs(-rfc)
 
'''<tt>921 rF:rFc  </tt>''' sets the DC bias of the DAC, please remember that this value has individual settings for each full 1 MHz band


== Improved CTCSS tone filtering / Parannettu aliäänen suodatus ==
== Improved CTCSS tone filtering / Parannettu aliäänen suodatus ==
Rivi 54: Rivi 56:


Level control does not work in RFC DAC CTCSS generation (works at least in 3.Yz).
Level control does not work in RFC DAC CTCSS generation (works at least in 3.Yz).
<bold>Solved. In later versions, 818 CtGAin must fit between 921 rfc and abs(-rfc)</bold>


Repeater mode needs two additional parameters: one to define minimum length of overs and another to define the number of overs to trigger the shutdown ID. This is needed to make the repeater as quiet as possible in case of kerchunking or somebody just ID:ing or calling another station with no QSO resulting.
Repeater mode needs two additional parameters: one to define minimum length of overs and another to define the number of overs to trigger the shutdown ID. This is needed to make the repeater as quiet as possible in case of kerchunking or somebody just ID:ing or calling another station with no QSO resulting.


There is a special build of the firmware with RSSI reporting to the handset MBUS line, this should be incorporated in the future mainstream builds. There is at least one SIO port available, maybe its application should be considered, too.
There is a special build of the firmware with RSSI reporting to the handset MBUS line, this should be incorporated in the future mainstream builds. There is at least one SIO port available, maybe its application should be considered, too.
Do the offset and multiplier parameters (881-813) work? Do they also work if the LO signal is divided to HF?

Versio 22. huhtikuuta 2009 kello 23.06

Nokia Mobira R58 series (band versions RB58, RC58 and RD58)

This page is intended to be a collection of modifications for R58 series radio, to be used for both operating radios and R58's used as repeaters, duplex gateways etc.


CTCSS generation/encoding for non-repeater use

Introduced at firmware 3.Yz, requires R58 firmware 3.Zi or or higher to operate as follows:

The RX front-end DAC can be used for generating CTCSS waveform for TX. The modification is easy and requires just two components, a polystyrene 100n capacitor and a 10k resistor to be installed on the A8 audio board beneath the P8 processor board. All settings are adjusted by the handset.

Solder points for the components
Components laid in place

Parameters:

01 GE:CtCSSt CTCSS frequency in hertz. For frequencies with decimals, use the nearest full Hz. eg. 118.8 Hz would be 119 and 74.4 Hz would be 74

816 PH:CtCGEn option rFcdAc selects the RX RFC DAC output to be used as CTCSS waveform generator during TX.

817 PH:CtHAnG sets the TOC time in millseconds. TOC eliminates the squelch crash at the receiving station, suspending the CTCSS tone transmission prior to the drop of the carrier.

818 PH:CtGAin sets the amplitude of the generated waveform, must fit between rfc and abs(-rfc)

921 rF:rFc sets the DC bias of the DAC, please remember that this value has individual settings for each full 1 MHz band

Improved CTCSS tone filtering / Parannettu aliäänen suodatus

Replaces 330kohm resistor and 100nF cap: Korvaa alkuperäisen kytkennän.

  >--- 22kohm ---+--- 22kohm ---+--- 330kohm ----- 15 nF ----> output
                 |              |         
                === 15nF       === 15nF
                 |              |
                 |              |
                GND            GND 

Capasitors can be between 10...20 nF, resistors 18...27 kohm.


Filter simulation

CTCSS generation/encoding for R58 repeater

CTCSS decoder installation for R58 (both repeater and non-repeater usage)

General-purpose outputs

DTMF decoder installation for R58 (both repeater and non-repeater usage)

Wiring R58 for external controller usage (both repeater and simplex gateway usage)

R58 firmware wishlist

The latest firmware is 3.Zi.

Level control does not work in RFC DAC CTCSS generation (works at least in 3.Yz).

<bold>Solved. In later versions, 818 CtGAin must fit between 921 rfc and abs(-rfc)</bold>

Repeater mode needs two additional parameters: one to define minimum length of overs and another to define the number of overs to trigger the shutdown ID. This is needed to make the repeater as quiet as possible in case of kerchunking or somebody just ID:ing or calling another station with no QSO resulting.

There is a special build of the firmware with RSSI reporting to the handset MBUS line, this should be incorporated in the future mainstream builds. There is at least one SIO port available, maybe its application should be considered, too.

Do the offset and multiplier parameters (881-813) work? Do they also work if the LO signal is divided to HF?